DIY

Power garage vise channel with your hands

Мощные гаражные тиски из швеллеров своими рукамиHi, to all fans to make something useful with his own hands. In today’s article I’ll try to describe in detail the Assembly of a very useful tool for every DIY. Namely, we will collect powerful grip of the metal profile. Surely everyone at least once dreamt of a powerful and strong grip, but a pair repels many from buying them great value. This art project will cost much cheaper than any sensible factory counterpart, and will be stronger than most of them, as in the factory counterparts often use alloys of cheaper metals to reduce the cost. By itself, the design of the grip limit, is simple, and therefore, some sophisticated skills of welding during Assembly is not required. Well, I think you should not pull with a long Preface, here we go.
To build a powerful grip you will need the following, namely:
– Metal corners (6 mm)
– Sheet thick metal (6 mm)
– The thick metal “U” shaped profile (6mm)
– A thick metal pin (18 mm)
– Nut under the pin
– A small segment of metal fittings
– The thin metal plate 2 mm (for setting gaps)
– Screws
– Amalina paint
Tools also need the following:
Welding machine with all necessary welding accessories
– Drill or drill press with drill bits
– Angle grinder with cutting and grinding discs
– Clamp
– Wrenches
– Tap for cutting internal threads
– Lubricating oil
– Screwdriver
Assembly vise:
Begin assembling the grip with the chassis. The portion in which longitudinally move the movable part of the clutches. This part should be cut out of thick sheet metal rectangle. The thickness of all metal components will depend on the ultimate capacity and reliability of the clutches.
Мощные гаражные тиски из швеллеров своими рукамиWe continue to build chassis design. Next, you need from profile metal bracket to saw off a couple a segment of the same length. The resulting crop from the area will need to be welded to a metal rectangle. To do this, so as not to miss the mark with the distance between the corners, do the following. Namely to take “P” shaped profile, which will move inside the chassis, put it in the center of a rectangular plate and sides dotting the corners.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиBetween “P” shaped profile and corners should be a small gap for easy moving of the channel. In order to provide a proper and uniform gap, we need to pick up some plate about 2 mm thick and put it between the corners and the profile. Then weld the brackets to the thick metal rectangle, which in this case is the base of the structure.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиPrivaris corners, remove the plate for setting the gap, and check how is “P” shaped profile, in the groove, if nothing interferes when you move, then continue. Next, you need between welded parts based on the weld the “spacer” thereby connecting the eyelids a couple of corners. So we get a full suspension. This spacer are cut from the same sheet 6mm metal.
Мощные гаражные тиски из швеллеров своими рукамиIt is not difficult to guess, after cutting out the spacers should be welded in its place to the corners. Weld should be the same as we had previously welded the corners to the base, namely, leaving a gap of 2 mm. So you put “P” shaped profile in place on top of him put two 2 mm plates, and then put the spacer itself. Clamps hold the corners in order to reduce the gap for welding. And then weld, proverjaem thus, all of the joints.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиRemove the clamp. And check feels like a “P” shaped profile, it needs to move freely longitudinally on the chassis. Making sure that we have everything in order zashlifovyvajut all welds, in order to give the workpiece the form of a monolithic part.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиGo to our previously used “P” shaped profile. Here it is worth mentioning its length. The length of this part of the structure can be any, then it all depends on your needs. The author of the handmade is cut off a length about 30 cm, more than enough to cover most needs.
Мощные гаражные тиски из швеллеров своими рукамиTo one side a “P” shaped profile, it is necessary to weld the metal plate, thereby making the plug in profile. This plate will have to serve as a focus, to move the profile. In this plate before welding it is necessary to make a through hole at its center. Through this opening will be a stud, therefore, the hole should be slightly larger in diameter than the chosen pin. Securely weld and zashlifovyvajut welds.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиThe next step is to make a detail, thanks to which will, there is a longitudinal movement. Of course, it could be the millet to the chassis to weld a suitable nut, but it turned out not very reliable. Therefore, the author made the following, and it took three nuts instead of one and welded them together, then further increased connecting a pair of metal plates. And wail this wrench the Assembly into the chassis. The main thing here is that the nut were parallel with the hole in the welded stub on the profile.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиThen make a handle for the clip. This will take the spike, which will be set to handle. At the end of the stud screw-on a couple of nuts, just wound the nuts have to be mounted on a small stud welded point. Next, we perform in the nut perpendicular through hole. Into this hole insert a piece of rebar (pre-sanded) and that it is not left on its edges welded on a nut.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиNext, you need to cut a couple of cuts from the metal bracket, the length of these parts should be slightly larger than the width “P” shaped profile. These parts will strengthen the locking “lip”. In order to have at any moment had the opportunity simply to replace those lips. In the corners needs to be done and cut holes in them with a tap thread for screw connection.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиGo to manufacture themselves lips, they will make metal plates with a thickness of 6-10mm. To cut metal workpieces under his lips, should be done a couple of return holes for attaching themselves to the corners of the lips. Further, using the grinder cut perpendicular to grooves over the entire area of the workpiece. Do this on each lip, with one of its sides.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиGradually we begin to assemble the design. Fasten the lip of the plate to a previously prepared parts. Corners with lips connected to each other using clamps (it is necessary in order to ensure their parallelism relative to each other after installation on the structure). And actually weld these corners, one corner to the movable part, and the second to real estate.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиFurther, in order to end up with the corners of the lips did not posiible in the back, you must do the following. Namely welded to the corners of the spacers, cut from plates, turning the corners into triangles in cross section.
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиAfter sanding all of our home, removing all corrosion, and welds. Then paint some amalloy paint. It is necessary for the preservation and protection handmade from the effects of corrosion. Mounted on the stud, tighten one nut and securing it in one position (see photo). This is to ensure that the stud is twisted together with the moving part
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиThere you go! The end result is a useful tool that will always come in handy
Мощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиМощные гаражные тиски из швеллеров своими рукамиHere is a video of the author of the homemade:
Well, thank you all for your attention and good luck in future homebrew projects

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.