DIY

Aircraft-Kristall for flying in the meadow

Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеAircraft type “Kristall” the most common model in the network. The options are endless. Construct a captivating simplicity and a small budget glider. except of course the sweet couple, the receiver – transmitter.
Did a lot of these simple designs. Already the summer came, intense summer season, produced a small foam airplane “pokolbasitsja” on the meadow.
Start with templates is executed on a fairly thick paper of 250 grams. And of course, the ceiling tiles are 4mm.
Самолет-крестолет для полетов на полянкеThe apparatus was conceived is not very small, so pick up a couple of tiles 50×50 cm
Mark and cut out parts of the airplane.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThe ailerons are cut out with a pair of imposing top as a template and fixed with needles.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеCut out wings, door wings, the profile of Fogelman and the upper and lower halves of the fuselage.
Lacked a bit of material on the horizontal part of the fuselage. It is collected from scraps of the right size and glued together from two halves,fix the tape on both sides and place under a press.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеInitially, the wing had planned to do together with the horizontal fuselage, redesigned that part. Doing a wing trim, so stronger than constructive.
Cut the fender, pickguard glued together and then cut the spar strengthening of 2×8 pine slats mm.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеChange details, the wing is under the press, glued the plate to the fuselage – in work.
To this element we can already fix the Elevator. Cut the inner face of the structure at 45 degrees and hung on the tape.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеSmall gaps between moving parts is necessary, otherwise probably jamming under load.
Самолет-крестолет для полетов на полянкеThis is all.
Cut and glued the lower part of the fuselage of two layers potolochki t,e, 8mm. Please note as located strip of adhesive on the titanium workpieces. On one lengthwise, another crosswise, cross shorter. When applying the glue on the workpiece, make the first strip on the edge, it is important to glue. Inside almost stroke crosswise as a pencil.
Самолет-крестолет для полетов на полянкеAgain change.
Самолет-крестолет для полетов на полянкеRemove the wing, loaded the fuselage under the press.
If before the connection of the parts to withstand a few minutes for drying the adhesive, under pressure, you can keep for twenty minutes. Certainly not fully dry, but grab well enough to continue.
Little subtlety, while Klein stood perfectly still, it can be well cut through with a knife. A day later it turns into quite a brick crust, which is difficult to cut and may distort the accuracy of the line.
Hang on the wing ailerons. To assemble the airplane better units and to unite them according the project progresses.
Cut off the inner edge of the Aileron at 45 degrees and hung on my favorite Scotch 3M super crystal. (There is only one SCOTCH-the rest of the sticky tape! Самолет-крестолет для полетов на полянке )
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThen mark out on the fuselage line attaching vertical elements on both sides. this markup will apply adhesive and install .
Самолет-крестолет для полетов на полянкеBut before you glue the wing. Again, apply the adhesive strips crosswise.
Самолет-крестолет для полетов на полянкеWhen the wing is installed , but not glued at all, check correctness of installation. The distance from tip of wing to tip of the Elevator should be the same on each side.
Then apply the glue to the bottom vertical fuselage to withstand drying long enough, about five minutes. If you catch the moment, when the bonding glue sets almost instantly, as Lecrin.
Самолет-крестолет для полетов на полянкеAdjust the upper plate, the booth. it is necessary to provide a cutout for the pad wing.
The moment caught and vertically grasped. Some friends to speed up the process use a hair dryer. Glue drying with a flow of warm air. Quite a normal acceleration process.Check the angle.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеIn this position, the airplane can be left for about twenty minutes approximately.
Milk pechenegam during the break.
Самолет-крестолет для полетов на полянкеWhile waiting, it is sometimes necessary to adjust the details if necessary.
Самолет-крестолет для полетов на полянке
When getting into the process of drying glue, after about twenty minutes you can continue.
Cut out the rudder, cut the inside face at 45 degrees, but with both sides and hung on plastic loops. Previously rubbing their large skin for bushiness, increasing the strength of bonding. It is possible to perforate with a needle from two sides, gives a much stronger bonding. Or to make, rolling like from my nail and the gears of the clock,partially meganisyou process.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThe slot beneath the loops make the blade sharpened on all sides Very badly. Otherwise it will crush the foam.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThe subtlety of the process linkage. First, apply glue to the tips of the loops on both sides. When installed in the slot, the glue itself will be smeared in the plane of the loop. Wait until grabbed, then again apply glue to the ends of the hinge and insert into slots.
Самолет-крестолет для полетов на полянкеPads on the aft fuselage at 45 degrees. Otrezal the edges of the strips diagonally and glued on both sides of the tail.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThese ribs do not allow the tail to curl under intense aerobatics from efforts arising from the relocation of the ruder and Elevator.
Mark and cut out long triangles gain in the bow for the motor.
Самолет-крестолет для полетов на полянкеAnd check the perpendicularity of installation.
Самолет-крестолет для полетов на полянкеDecorated with colored tape.
My favorite thing to do.(do planes not to fly, for color Самолет-крестолет для полетов на полянке )
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеWhen working with tape, often wipe the glue away with a knife blade. Otherwise cutting will be bad stick and twist the line. Can alcohol, gasoline, Shoe or simply cloth. (only from the side of the butt to take your fingers behind the blade! Самолет-крестолет для полетов на полянке )
Самолет-крестолет для полетов на полянкеComcate trim and bond them in a pile, or on the table and other items may remain colored adhesive from the film is necessary to wash already with gasoline.
Самолет-крестолет для полетов на полянкеPonytail and blue Cabinet.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеOn the substrate from promotional films ORACAL or some other firm is cut from black adhesive tape strips for the edging.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеGlue a strengthening of the wings of the skewers.
In the right wing near the spar and glue to the cords.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThe gain on the lower part of the nose. Ski, to do it I will.
Самолет-крестолет для полетов на полянкеReady glider airplane.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеEquipment removed from a broken model.
Not pull out, carefully separated all the parts.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеRemove the masking tape from the servo, along with glue and it is clean and beautiful.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеNo longer glued, mounted on a frame of 4mm plywood and fastened with screws.
Under the diameter of the screws pick up the drill. Inspection hole, is quite tight the screw was.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеTake the tape off in places gluing framework. Titanium does not stick to it.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеCut motors with the stock.
Stuck on the spout was fixed with tape.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеWelded the Scotch iron of course easier to do it on a disassembled airplane. Somehow missed this moment.
Самолет-крестолет для полетов на полянкеControl horns on rudder Elevator of clear plastic from the lens of the laptop screen. With a thickness of about 06, quite viscous and durable plastic, to break problematic. Rubbed a large skin for bushiness increase the strength of bonding.
Самолет-крестолет для полетов на полянкеForgot to embed the reinforcement to the Elevator. Split a bamboo skewer and glued from the bottom, fix with masking tape.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеThe tips of the rods on the classics, g-shaped squiggles of paper clips taped nicknames and fix the shed.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеMotor, propeller, ESC, receiver..all you can fly.
Самолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеСамолет-крестолет для полетов на полянкеFLEW!!!
A sample of the pen.
Everything is normal, the center of gravity in place. The little battery came off…happens. Now Pasabahce her harder.
Fly soul…
Today I flew in a large field in a fresh breeze.
Самолет-крестолет для полетов на полянке

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Check Also
Close
Back to top button
Close

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.