DIY

Brutal spinner with your own hands

  • Assembly instructions brutal spinner at home
  •  Such a thing as a spinner in recent times gained immense popularity. Seemingly simple thing, which, by its very simple, but interesting, had been in the hands of almost every teenager and not only.

    Due to its popularity, every owner wants to have a unique spinner, which could be used to show off in front of others. Most of the spinners are made mainly of plastic and metal inserts. Over time all things wear out, are no exception and spinners. Due to the fact that they are constantly falling, they gradually begin to fall off parts and wear surface. As a result, they do not look attractive.

    Rarely thought about the creation of the original spinner that may look brutal and not break. Now we’ll show you how to make a spinner out of things that do not require a long search, but it is already available. Let’s get started.

    Брутальный спиннер своими руками

    Брутальный спиннер своими руками

    For the manufacture of a spinner you will need the following material:

    1. A Bicycle chain;
    2. Coin 27 mm – 3 PCs.;
    3. A wooden block of size 15 by 15 cm;
    4. Nut turnkey for 10;
    5. The bearing from a computer hard drive;
    6. Tapping screw – 2 PCs.

    In the process of making the spinner will need the following tool:

    1. The Bulgarian (LBM);
    2. Wire Cup brush for angle GRINDERS;
    3. Any metal rod with diameter of 1.5-2 mm, length 10 cm;
    4. Hammer;
    5. Vice;
    6. Screwdriver;
    7. Spray non-stick;
    8. The welding machine;
    9. Cold welding;
    10. Pasta GOI;
    11. Grinding machine.

    Assembly instructions brutal spinner at home

    To begin with, take a Bicycle chain. As a rule, it is dirty, possibly with elements of rust; grind it grinder with a metal brush that she took a shiny look.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Take cleaned the chain and outline her the edge of the coin, what would the chain be completely covered in a circle. Look at what chain link you need to separate that would be enough for one turn of the coin. Coins taking any your taste, most importantly, would respect the right diameter.

    Брутальный спиннер своими руками 

    To separate a chain link put the screws to a metal rod, the finger circuit in the right place. This can be done with hood, which you can easily do yourself. Knock the finger on only one side of the circuit, which would then be put back.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Ready a piece of chain that we got, wrap the coin and if the holes of the coupling circuit match, hammering a finger back.

    Брутальный спиннер своими руками

    It happens that the holes do not match and have to pull the chain. This can be done by squeezing in the grip of the two units that we are going to connect. Likewise with the other two coins.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Put the nut on a wood block and around our coin blanks, that they would fit snugly to the nut. This is to ensure that the spinner has a well-balanced.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Will Brysam non-stick spray on our billet in order to avoid drops and don’t need to cook our of the workpiece at points of contact without affecting the nut. Similarly weld the workpiece with the other hand.

    Брутальный спиннер своими рукамиБрутальный спиннер своими рукамиБрутальный спиннер своими руками

    Take out unnecessary computer hard disk drive bearing and machined it at the upper edge at risk using the same vise and GRINDERS.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Now you need the bearing to put in the middle of our device for cold welding, the surplus which you can then clean off the GRINDERS with wire brush what would it look attractive.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Find 2 screws prettier and process of the cap to Shine on the grinding machine. What if this lesson is not to prepare nails need to be any device with a cartridge where you fix the screws. This device can be a drill (when Stripping you just need to keep the cartridge), or, if there is a free cartridge, install it on any wooden handle.

    Брутальный спиннер своими руками

    Cut the 6 mm screws from the cap and machined threads so that they sit securely in the bearing. For greater reliability, they can be planted on cold welding. Hammer firmly put the screws into place.

    Брутальный спиннер своими рукамиБрутальный спиннер своими руками

    Your spinner is ready, you can go to brag. You doubly deserve it, because spinner made by your hands, and he’s really good looking!

    Watch a video detailing you can see the process of making a spinner with your own hands:


    Source:

    rukikryki.ru

    Show More

    Related Articles

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    Back to top button
    Close

    Please disable your ad blocker

    We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.