DIY

Quiet trimmer of the grinder with your hands

  • Instructions for the manufacture of trimmer grinder at home
  • When it comes to summer time and inevitably grows up around the house unwanted vegetation, we get your trimmer early in the morning and loud noise of the engine Refine the area. Neighbors not lucky today.

    This article will show you the way how to make unpretentious quiet trimmer from parts that are available in most households. It is worth doing only for the reasons that:

    1. Does not require fuel;
    2. Few weighs;
    3. Quiet;
    4. Simple to manufacture.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    For the manufacture of trimmer from the grinder will need the following material:

    1. Unnecessary small angle grinder with aluminium gear;
    2. Connecting nut M8 – 2 pieces;
    3. Bolt M8 a length of 4 cm;
    4. Nut M8 – 4 PCs.;
    5. Nut M12 – 2 pieces;
    6. Screwdriver;
    7. The prop adapter is ¼ inch under a spanner head;
    8. Metal tube with a diameter of 30 mm and a length of 130 cm;
    9. Washer with outside diameter 30 mm inner 10 mm of a thickness less than 2 mm – 6 PCs.;
    10. Metal rod with thread of 12 mm length 80 cm;
    11. A metal rod with a thread diameter 8 mm length 80 cm – 2 pieces;
    12. Bearing 8х22х9 mm – 3 pieces (one open, the other closed);
    13. Rubber hose with an inner diameter of 20 mm with a wall thickness of 4 mm, length 10 cm;
    14. The plug on the sewer pipe with a diameter of 50 mm;
    15. The Withdrawal D50х35гр;
    16. Clutch repair D50;
    17. PVC adapter 50х32 mm;
    18. PVC pipe 32 mm – 10 cm;
    19. PVC pipe 25 mm – 10 cm;
    20. Metal clamp with a diameter of 35 mm;
    21. The yoke tube, with nut 1 ½ inches.

    In the process of manufacture of the trimmer from the grinder, you need the following tool:

    1. The key for grinders;
    2. Phillips screwdriver;
    3. Flat head screwdriver;
    4. Vice;
    5. Hacksaw;
    6. End cutters;
    7. Grinding machine;
    8. Set of dies;
    9. Set of drills;
    10. Roulette;
    11. Duct tape;
    12. Hammer;
    13. Pliers;
    14. A set of keys.

    Instructions for the manufacture of trimmer grinder at home

    We will need a grinder that was spent. Most importantly, she was a working gearbox. Unscrew the cover and then the gearbox itself, remove it along with the rotor. Hold the rotor in a vise and saw off the reducer as close to the plates of the rotor.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    Fix the reducer in a Vice and end cutters remove remnants of the winding.

    Тихий триммер из болгарки своими руками

    Also usually remove the top of the fragile surface of the shaft at the length.

    Тихий триммер из болгарки своими руками

    Hook rotary wheel any chisel or screwdriver, remove it and in place of its planting remove the upper surface of the shaft.

    Тихий триммер из болгарки своими руками

    On grinding machines processed the resulting shaft diameter up to 10 mm.

    Тихий триммер из болгарки своими руками

    Fasten conveniently reducer in a vise and ground down the shaft threaded with an internal diameter of 8 mm and a length of 15 mm.

    Тихий триммер из болгарки своими руками

    Tight preporacuvam on this thread connecting nut M8.

    Тихий триммер из болгарки своими руками

    Install the reducer in a vise, that you could drill a hole in the other shaft with a diameter of 9 mm and a depth of 10 mm. It will be a spot for the prop adapter.

    Тихий триммер из болгарки своими руками

    Hold the processed shaft in a vise and drilled through the middle in 2 mm from the end of the shaft hole with a diameter of 2 mm. From the prop adapter are also in the seats drilled holes 2 mm in diameter. Mating part with a nail.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    Make a mark on the metal tube at a distance of 65 cm from the edge. Find a washer that will put on a thick rod and tight and will be able to pass freely through the tube.

    Wound on the rod nut M12, for it put a matched washer and fix the second nut so that the rod is not protruding from it. It will be a pusher for the bearing. Put the rod so that the washer was on a level with the beginning of the tube and primitive electrical tape on the rod at the place where our inflicted label.

    Тихий триммер из болгарки своими руками

    Cut from rubber hose 2 rings of 9 mm and one 50 mm long. Make a cut along them. The bearings of the closed type are placed in short-elastic open disposable the middle of the long bands.

    Тихий триммер из болгарки своими руками

    Installed a long rubber band with a bearing pusher and press-fitted it into the tube in electrical tape on the rod.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    On one side of the tube to drive one washer to a depth of 1 cm, put it on the bearing with the rubber band on them and another washer. Egged on by inside of the tube wall that the washer was unable to pop up.

    Тихий триммер из болгарки своими руками

    Two thin rods firmly connected with a connecting nut and insert inside of the tube until the coupling nut abuts the bearing. With the free edge of the tube as well insert the washer, the rubber bearing, another washer, egged on by the phone. Take out the rod at 20 cm and cut it at the edge of the rod drill a hole 2 mm in diameter.

    Тихий триммер из болгарки своими руками

    Fasten the sewer stub to the place where stood the casing and connect the rod with the hole on the propeller adapter through the nail.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    Placed the cover on the drainage reversal in the opposite direction from the shaft, the rotor, the cap to put a repair coupling, then PVC adapter lower side to the top, he threaded PVC pipe 32 mm and under 25 mm. What would the tube tightly joined each other do they have the incision.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    The place where the tube is 32 mm in contact with the tube of 25 mm, clamped tightly by a clamp. On the other side of the metal pipe rod cut at 7 cm from the edge and firmly fix the rod at the 2 nuts against the washer.

    Тихий триммер из болгарки своими руками

    Bolt M8 clamping in a vise and drill a through hole with a diameter of 3 mm at a distance of 2 mm from the cap. Put on a bolt two washers and loosely fasten the nut. Between threaded washers in our line, which we mow and tighten the nut. Tightly preporacuvam the bolt line to the gearbox.

    Тихий триммер из болгарки своими руками

    Тихий триммер из болгарки своими руками

    In a convenient location on the metal tube fasten the tube clamp with nut and screw it to the handle of the grinder, it is perfect.

    Тихий триммер из болгарки своими руками

    It remains only to fix the tip of a metal rod in a drill and you can go to arrange in order around the house. The neighbors will definitely envy to review your newly made device, because it is not bulky, it is comfortable to hold, and the noise it can not be compared accurately with the trimmer from the store.

    Watch the video, which you can see in detail the process of manufacture of the trimmer of the Bulgarians:


    Source:

    rukikryki.ru

    Show More

    Related Articles

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    Back to top button
    Close

    Please disable your ad blocker

    We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.
    Cookie Box Settings