DIY

Do Hamutal from the stabilizer link

For making a neat and durable clamps, wire need Hamutal. This tool will allow you securely tighten the hose to the pipes and fittings, tie poles to put a net on poles, etc. to Make Hamutal can be based on the stabilizer link from vehicle.

Делаем хомутатель из стойки стабилизатора

Materials:

  • strip or sheet steel 3 mm;
  • any metal with a thickness of 15-20 mm;
  • stabilizer link;
  • a wooden rail.

The process of making commutates

For the Assembly of homotheties need to prepare the steel strip 30х250 mm, a length of the stabilizer 100-150 mm and 2 plates of steel with a thickness of 15-20 mm size 25×30 mm.

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

In pre-polished Desk need to make a longitudinal cut, not bringing it to the ring He runs 10-20 mm. grinder mounted with a cutting disc a cross section of 2.5 mm, which will continue to fill him with enough thick wire.

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

The prepared strip with one end needs to be cut under the triangle. Received sharp top cut and it is cut to prevent slipping of the wire.

Делаем хомутатель из стойки стабилизатора

Next you need to make a thickening on the band closer to the cut edge. To do this, the sides are welded lining. You can apply thick layers of welding and then cleaned them on the bevel, the part turned out the most accurate.

Делаем хомутатель из стойки стабилизатора

The workpiece is drilled in the center welded thickening. In the resulting hole must pass stabilizer. It is important that it can rotate, so the hole is 0.5-1 mm wider.

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

For the rest of the thickened part of the strip required to make the handle. To do this, from thin strips cut 2 pads, and installed the rivets. Also the handle can be made of PCB with plastic or other moisture resistant material.

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

To use hematocele to tighten the hose, you must first prepare the clip from the wire. For double clamp it screwed onto the hose so to get 2 rings located close to each other. Then the wire is formed between the rings in half. If you need a regular clamp, the wire formed a loop.

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

Further, regardless of what the clamp is installed, you need to dilute the edges of the wire and insert between them on the loop the nose of homotheties. Then the ends of the wound into the slot of the rack.

Делаем хомутатель из стойки стабилизатора

Rotation of the rack, tighten the clamp, and then rotate Hamutal aside from a persistent loop. As a result of bending the clamp will not weaken.

Делаем хомутатель из стойки стабилизатора

You can then bite off the excess wire and tap the short edges so they don’t seem to fit.

Делаем хомутатель из стойки стабилизатора

Делаем хомутатель из стойки стабилизатора

Watch the video

Source:

sdelaysam-svoimirukami.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.
Cookie Box Settings