DIY

Unusual wall shelf with his hands from improvised means

Необычный настенный стелаж своими руками из подручных средствGood day lovers of building something with their hands. In Today’s article I will try as much detail as possible to describe and show how to make a very unusual and interesting home-made to store small tools or a variety of nuts, bolts, screws, etc .. This home will be finished in a very unusual form factor and will not only decorate your garage or workshop, but also to surprise your friends and acquaintances. Itself home-made, as expected, will be made of the most simple and available materials, so you can afford it could be anyone. Yes, and some of the structural complexities in it, and its Assembly will not cause you problems.
For the original rack will need the following details, namely:
– Flat metal profile (width of about 30 to 45 mm)
– Cut thick-walled metal tube (20-40 cm)
Bolts
– Nuts
– Washer
– Bearings (such that sat tightly in the tube)
– Stud
– The banks and screw covers
– Wooden plank
– Screws
– Paint (optional).
Tools also need the following:
– Drill press or a regular drill with drill bits
– Ordinary wood saw
Welding machine with all necessary welding accessories
– Wrenches
– Screwdriver
– Angle grinder with cutting and grinding discs
Construction area
Marker
– Hammer
– The range.
The making of an original rack details:
Take a flat metal profile (in the home will need a lot). Of a metal profile is first necessary to cut out 10 identical in length and width segments. For this you will need a ruler and a marker, which divide into sections with the profile. Length of these segments for each individual, then it will be clear what it is, and you for yourself decide how long to saw these 10 parts. Mark 10 parts on the profile, take a grinder with a plastic cutting disc and nephilium segments.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствThen for safe operation of the diys you must do the following, namely, to take and to round the corners on one side cut profile of the segments. It can be done in several ways. You can do so as he made it by handmade, to take the grinder to put her on a grinding disc and grind the corners or can be cut from the same grinder, but with the cutting disc. But in that and in other case I recommend to apply a marker template to do the rounding is to be maximally similar to each other.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствThe next step, these same strips that were produced from the profile just that, you need to connect the 5 pieces, that is, we have 10 core parts, will be a two piece. For this we select the appropriate diameter pipe (preferably thick-walled, so as to weld something to the pipe will be easier) put it on the table, and spread our “rays” as it is shown in the photo below. Weld the beams to each other, but not privativa them to the tube itself.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствThen do the same thing with the rest of 5тью rays. Here it should be noted that the two specific billet in our case should be as symmetric, otherwise home-made Assembly will look very clumsy. So we put the rest of the rays on the previous and weld them together (see photo).
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствThen you need to go through holes on the edge of each beam of the two blanks, as already mentioned, the workpiece should be symmetrical. To symmetrical holes, it is desirable to be weld together the workpiece, literally a couple of spots.
Необычный настенный стелаж своими руками из подручных средствCook blanks between them, note the space under the hole piercing. The holes should be placed at the outer edge and centered relative to the sides. The proposed marker holes and proceed to drilling. Holes in a thick metal is best drilled using the drilling machine, in this case, the holes turn out as neat. It is also important to know that when drilling thick metal, there is a risk to ruin expensive drill bit to overheat it. To avoid any lubricating oil, so you reduce the friction and the drill will enter smoothly.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствDrilled all the necessary holes, you need a hole welded nut, the screwing of the bolt (nut should be outside). To center the nuts with the holes, you need to screw the bolts into the nuts so that the bolt was slightly out on the other side of the nut. Then insert a bolt with nut in hole and weld nuts. Do it with both five-way presets.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствThen it is necessary to interconnect these five-way presets. But rather to establish and fasten them to the pipe around which are placed. The length of this pipe is also selected arbitrarily as the length of the rays, the longer the pipe, the more space will be ready on the shelf. Determine the length of the pipe, cut it on the ends to attach our billet and weld, not forgetting about the fact that the beams should be parallel to each other.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствIt is not difficult to guess the pipe must rotate around its axis, so if she could do it, you need to put it on the shaft with the bearings. That is, first in the pipe “will supresses” bearings, and then install the shaft. Pick up these bearings, so they fit more tightly inside the pipe. Hammering bearings into the pipe with a hammer.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствAs the shaft will use a suitable diameter pin. Pokes a pin through the pipe, installed bearings, and to fix it there, tightening both sides on a nut through a washer.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствGo to manufacture of fasteners. The author of homemade decided to assemble the wall mount, you can quite a bit to change the design and assemble the table mount. For this attachment to saw four equal segments of flat metal profile. Two of them will keep the shaft, and the other two will be the last two. Two done one through-hole (below the shaft), and the other two by two through holes on the edges (under the fixture to the wall).
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствYet put aside two plates with one hole, and take those in which two holes. They must parallel connect them, it will cut out a couple of struts about like in the photo below, and cook them together so that the end result is a rectangular “frame”.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствAt the corners of the frame perpendicular to the frame, parallel to each other, weld the delayed two plates. As mentioned, they will hang the rack to strengthen it is possible to weld additional spacers (see photo).
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствConnected between the stand and the rack. While homemade is not quite like a rack. For storing the little things we use banks, the banks themselves will set on wooden plates. 5 cut into planks of the desired length, fasten them to the lids from cans, and set the plates on the design (see photo)
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствYou’re done! Now we need only to paint our home. Well, and of course installed the rack, filling it with any useful detail.
Необычный настенный стелаж своими руками из подручных средствНеобычный настенный стелаж своими руками из подручных средствHere is a video of the author of the homemade:
Well, thank you all for your attention and good luck in future projects the homebrew!

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.
Cookie Box Settings