DIY

The small maneuverable biplane model

Биплан небольшая маневренная модельDid quite a lot of variants of the biplane for indoor aerobatics and streets. A couple of cars training options broke learning the maneuvers.
Advantages of this type of models is undeniable, the simplicity of construction (as it not strange sounds), excellent maneuverability allows you to train in the standard school room. Even on the half of the room! If you meet the weight to one hundred thirty grams in the span of 700 mm. However in the competition for a number of reasons this did not stick….
Among the shortcomings, it is difficult to provide a rigid coupling biplane box with the fuselage, difficult to repair due to its sophisticated design. When performing aerobatic hall complex class F3P bad comes to flying difficult, the drawing of the figures is difficult to read.
Must clear of driving can be achieved by working with the design …but something did not go this route.
After consideration of the layout and General appearance, was removed from the drawing copy and cut the templates for making.
Begin fabrication by bonding a pair of sheets potolochki, after cutting off a chew from the lower side edges at a distance of about 4 cm and Then applying templates, mark out and start cutting out parts.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельThe wing with the trim gain at the front edge. Mark the place of gluing the pads and apply the glue along the contour of the workpiece. The middle shade is not too frequent layers of glue.
Биплан небольшая маневренная модельFor convenience, pour titanium into the bottle from under the paper glue with a thin nozzle. It is more convenient to work with. The tip is cut obliquely, when applying the glue turn a slant in different directions, it is easier to adjust the amount of vitacevo glue.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельCut the wing and glued the rack to gain eight in 2 mm. All fix with masking tape on both sides. Then cut the rack gain in the Elevator four in 2 mm.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельThen hang the ailerons are pre-cut adjacent to the wing side at a forty-five degrees. First glued the beginning of the Aileron is pre-tilting it at a forty-five degrees, then the other end. And in the middle a couple of strips. Flip the Aileron covered and four more strips of tape with a slight tension.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельPrepared Reiki the gain on the horizontal plane of the fuselage. The size is cut just with scissors, near the Elevator a little kick rail. Gluing fix with masking tape.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельThen cut off the little wings and hang them over the tape on both sides, as the ailerons.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельThen hang the Elevator.Until all with the horizontal part.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельThe lower part of the fuselage is glued from two layers potolochki, once the nozzle install a safety ski Reiki eight in 2 mm.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельThen glued the slats of the gain to the struts biplane box. The size of two to 4 mm. Fix with masking tape until dry.
Биплан небольшая маневренная модельStart to paste over with duct tape. Wide blue and yellow stripes are quite simple. Stop at the squares. On a substrate of a promotional film paste black tape and cut it into oblique squares.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельSeparate each square with a triangular knife glued to the fuselage one at a time.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельFor the exact positioning of the pattern on the reverse, I bring the fuselage to the window and to the light, mark the position of the picture.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельAround the canopy with thin strips of black tape.
Биплан небольшая маневренная модельSome details of the gluing of the wing. Paste a strip of tape to the desired location and resting against the end of the amplification is cut with a margin. Then cut the strip at the corner.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельStripes on the wing and cells, the Elevator is also plastered.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельLine on the horizontal plate of the fuselage mounting vertical plates. At the bottom of the strip 8 mm from the top four. Glue the lower part of the fuselage.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельWhile glued together, mounted box stand wings and glued all together..
Биплан небольшая маневренная модельБиплан небольшая маневренная модельThen brushed 4 mm plywood cut out of the frame to install the servos. Mark the holes for screws and immediately savelives.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельGlued the frame servo mount for the ailerons, install it.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельOf bamboo skewers on the classics make the thrust with the tips of the paper clips taped with thread and glued fix.Pamaciau excess glue with a paper towel.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельMount the traction control on the rocking servo and mark the position of the length to the bend of the Aileron.
Биплан небольшая маневренная модельThen remove with a rocking cut to size and the second joint of the shrink tubing with fixation of the second adhesive.
Биплан небольшая маневренная модельIt is now possible to collect and stick into the foam triangles on the ailerons.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельMark the position of the servos on rudder, Elevator on the basis of long rods. Glued frame, cut holes for the servos in the foam. Secure the servos with screws.
Биплан небольшая маневренная модельThen glue the upper vertical fuselage’m picking up foam triangles and needles.
Биплан небольшая маневренная модельThe advantage of the layout of the biplane to the face, all servos and traction control are mounted on the fuselage. It remains only to put the box of wings and hold the traction control on the ailerons.
Биплан небольшая маневренная модельFor stiffness in the wing box glued twigs from the Mat thickness of about two to 3 mm. Glued next to the rails reinforcement.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельWhen everything is glued together cut strips to strengthen the tail section, cut faces at a forty-five degrees and cut the tube holes of relief.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельTraction control on the ailerons will be doing from carbon rods 1 mm. Open daddy “coal”, find suitable sticks, mark out, cut to size.
Биплан небольшая маневренная модельShrink on the joints and assemble the thrust, the wings glued to the Central thrust in the middle of the wing, then put on heat shrink , fix the fix and rebuff the soldering iron.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельOn the product rods glued the circles left from the strengthening of the rear fuselage. They glued the top and bottom.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельReady case.
Биплан небольшая маневренная модельMark the triangles enhance motor stuck on the bow, then mount. Fix with masking tape. After the glue has dried install the motor.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельThe screws are definitely teetering.
Биплан небольшая маневренная модельSome control components are mounted on a Burr from the shop “everything for sewing” agrimony fixed on double-sided tape for mirrors.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельTests management.
A small photo what the result is.
Биплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельБиплан небольшая маневренная модельThe flyby was held in a strong wind. Talking and flying did not work, only the plane in the air to keep.
Landed a whole.

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.
Cookie Box Settings