DIY

Decorative garden windmill with your hands

Декоративная садовая ветряная мельница своими рукамиHello! In this article I will try to describe you in detail and show how to make an interesting decor item for your garden plot. Namely, we gather, garden decorative windmill blades which will spin in the wind. This art project fit perfectly into the garden with a large area because by itself, the art project will be very large. To allow to collect this home-made be able to absolutely everyone, as it will generally assembled from cheap and readily available materials and using simple tools. Well, I think you should not pull with a long Preface, here we go.
This decorative garden windmills we will need the following, namely:
– Timber 40*40*2500 about 8pcs
– Timber 40*20*1500 – 2pcs
– Lining 13*approximately 1500 25pcs
– Stud M12 – 1 piece
– Corners 40*40*2500 about 5pcs
– Bearings under the pin – 2pcs
– Plywood, 12-20mm – 1m^2
– The clypeus a semicircle of 2 m – 4pcs
– Nails 500g
– Screws 500g
Nut M12 – 10 pieces
– 2pcs metal washers
– Impregnation, lacquer, etc.
Of the tools we also need the following:
Hacksaw
Wood saw
Construction area
Pencil
Roulette
Jigsaw
Screwdriver
Hammer
Planer
Pen or core drill
Manufacturer of garden decorative windmill:
Self-production should begin with a frame handmade, as a material for the frame was used with a beam size 40*40*2500 such bars we will need about 8 pieces can Not exactly say the number, so how can there be marriage in the end either the marriage of the timber. For the case we need to saw of the selected timber is the next workpiece, namely: 4 cut at 100cm, 4 cut to 24 cm, the 4 lines at 44 cm, 5 lengths of 51 cm, 2 cut at 60 cm, 2 cut at ~42,5 with a saw cut at 45 degrees on one side and 2 cut at 38 see the same with the saw cut under 45 degrees (see photo).
Декоративная садовая ветряная мельница своими рукамиBegin assembling the frame construction of the blanks, sawed informed we need to collect two of the same trapezoid. Trapeze will assemble the pieces with lengths of 100 cm, 24 cm and 44 cm Bonding bars between a length of at least 100mm. At this stage everything must be done very carefully and exactly, as if the frame will curve, then this mill to make smooth will be very difficult.
Декоративная садовая ветряная мельница своими рукамиGathering two flat trapezoid, we need to combine these into a single three-dimensional trapezoid. To connect them together will be the remaining bars 24 and 44cm. This should be done so, put the first one trapeze to the floor at its ends perpendicularly to put the bars (at the top short and bottom long), then gently lay second and twist them together with screws. In the end we should get something like the photo below.
Декоративная садовая ветряная мельница своими рукамиGo to the Assembly of the upper part of the frame, will collect until the very base without a roof. For this framework top we need the bars at 60 cm and 51 cm. is Put on the floor parallel to the two bars at 60cm, and in between on the edges put a couple bars on the 51. That is, you should now have a square with the size 60*60cm. The fastening of the bars and then we need to tie a couple bars of “spacers”, they fasten parallel to the 60 inch bars inside the square.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиNext, take the bars with sawn off at a 45 degree edges. We need to tie the edges as it is shown in the photo below. It is important that these elements were as equal as possible otherwise it will be a lot of problems with the fit of the roof and the rails should be flush with the ground. Also these two elements pasted together the remaining stick
Декоративная садовая ветряная мельница своими рукамиThen connected the two parts of the frame. Connected so that the roof was made from all sides at the same distance. Since the connection will still load no big load it is recommended to fasten these parts together with a large number of screws, about 6-8pcs. Frame ready, and I would recommend you to impregnate her any oil impregnation, to do it not necessarily, but thanks to the impregnation of a lifetime handcrafted and will last.
Декоративная садовая ветряная мельница своими рукамиGo to the skin, it’s not the most difficult stage of construction, but probably the longest. There is nothing ordinary, we put the piece of siding into place, mark with a pencil the excess, then sawing off the excess and use a hammer and nails to nail the segment in its place. Thus sheathe the entire trapezoidal part, and hem the top, the roof itself is not touch.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиNow we need to install the rotating shaft for the blades. Shaft we have mounted on bearings, so we absolutely need to secure suitable bearings at the top and make it exactly parallel to each other. The bearings themselves, it was decided to score the plywood sheet. To do this, cut a sheet of plywood with the required dimensions and install it in the upper part with bars (see photo).
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиNote the space under the hole, making sure labels are in place, begin drilling. The diameter of the holes should be slightly smaller than the diameter of the selected bearings so that the bearings are tightly curled up in your seat and not hanging in it. This kind of holes you need to drill the pen or a core drill.
Декоративная садовая ветряная мельница своими рукамиNext, remove the plywood blanks, hammered the bearings and set the workpiece back into place. Now we have already installed the bearings to insert the pin. In order that the stud rotates due to the bearing and did not take off from its landing spot, you need both sides of each bearing, and tighten the screws. When installing the screws not to overtighten, as it can bend the pin and gently rotate it will not.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиUntil saw off the excess part of the pin and then move to the skin. Now we need to sheathe clapboard front and back. Then have a little string up with the front part, because we have to accomplish a through hole pin. To do this, install the paneling next to the pin and determine the height of the hole. Done on the center piece of the hole on the height, then set the workpiece in place, pushes through the hole, pin, pencil, meet the speakers over the edge of the part and cut down their.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиNext, nail the roof, the roof I recommend to do the following, namely, to cut immediately the necessary number of segments of the lining, joining them together and in a single layer, nailed to its place. Then nailed the corners, where it is needed.
Декоративная садовая ветряная мельница своими рукамиGo to the manufacturer of the propeller. A prop we will need two bars 40*20*1500. At their center is necessary to make a through hole with a diameter equal to the diameter of the studs. Then to two bars can be connected to each other in one cross, you must do a couple of grooves as in the photo below.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиAt this stage we have finished the cross, so to, when we secure the crossmember it could rotate in the wind, it is necessary to set the angle. To do this with a circular saw or a jig saw will not be difficult. But I went the hard way and used a hammer a chisel and a Jack-plane (see photo).
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиBy making the bevels on the bars, they need to tie the tie bar as in the photo below. The quality of the cross I used a semicircular door casing. Screwed them at a distance of 30 mm from each other, the most extreme cross member was 50 cm and every 5 cm shorter than the previous one.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиIn principle, at this stage, you can stay if you are satisfied with the result. But for the decor I decided to make the door and window, there is no comment, because everything is simple. You can go ahead and decorate your home as you like.
Декоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиДекоративная садовая ветряная мельница своими рукамиEverything is ready, in the end, we had a very interesting garden art project that will delight you and your guests.

Sell the homemade or custom-made. Email me or leave a comment to discuss the details.

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.
Cookie Box Settings