DIY

Simple screw backwater “slingshot”, for convenient operation with long

Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиHi, all fans of building something useful. Often when working in the workshop is such that you want to prepare or join anything long much acting outside of your table. And work with any hanging without anyone’s help is problematic. So in today’s article I will try as much detail as possible to describe and show how to make a roller staking on wheels. This tool will help you to maintain anything, and it will greatly facilitate your life. A tool itself is quite compact and lightweight, so it will not take much space of your workshop/garage, also it will be installed castors for easy movement around the garage. Well, I think you should not pull with a long Preface, here we go.
This simple support will need the following, namely:
– Thick-walled pipe
– Bearings of suitable diameter
– Metal pin thin and thick
– Nuts in the pin
Bolts
– Washer
– Sheet metal
– Square metal profile
– Furniture wheels
Tools also need the following:
– Drill press or a regular drill with drill bits
Marker
Construction area
– Angle grinder with cutting and grinding discs
Welding machine with all necessary welding accessories
– Line
Making simple props:
Let’s start with the manufacture of the pressurization rollers, these rollers the object lying on backwater will easily move forward and backward. The rollers will make a thick-walled tube. Pipe sawn off two identical cut approximately 10-15 cm.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиPreparing sections of tube of the desired length and diameter need to match some bearings. Outer diameter of the bearings must be matched with the inner diameter of the pipe. Bearings should be tightly seated in the tube, that is to zapressovyvajutsja. Press-fitted in each of the pipes at the two bearings as shown below.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиThen bearings must be installed on the shaft. As the shaft will use a pin, a suitable diameter. From studs sawn off cut of such length that on the protruding part can be screwed a couple of nuts on both sides. Sawn off, install and fasten the pin with a pair of nuts, so that our ready-made rollers located at its center.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиThen you need to make a so-called “slingshot”, which is secure our videos. For this slingshot will need a sheet of thick metal which should be cut three narrow rectangle, one long and two equal shorter. About the same as the author of this handmade. Note the desired length with a ruler and marker, then pick up a grinder and saw off the desired portion.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиDrank necessary the above mentioned blanks, you connect them to each other, to connect them the following way. Put length. The workpiece on the table, to the edge, perpendicular to the weld the shorter the workpiece, when welding using construction area to obtain the maximum angle. Do the same thing with the other cream. In the end we’ll get a “P” shaped detail, as pictured. It is worth noting you should fully cook all the joints and preferably after welding grind the welds.
Return to our videos. Videos need to connect with a “P” shaped workpiece, is made just, and thus we have to get “slingshot” and will put items. Weld it to the pin “P” shaped workpiece, otherwise the rollers cannot rotate on bearings, the rollers should be welded at an angle of 45 degrees relative to the base.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиThen you need to make a mount for our “slingshot”. As the mount will use the same metal pipe that was used in the beginning for the manufacture of rollers. Sawn off this time from this pipe segment length is not more than 5-7 cm
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиLater in sawn-off segment of pipe should be done through hole, right by her side (center). In order to do this conveniently, it is best to use a drill press, if you do not, then no problem you can do without him, but without him this would be much more difficult. Hold the pipe in a vise and done exactly perpendicular to the through hole.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиThen a section of pipe welded to our “slingshot” bottom exactly at its center. Also need to weld on all the area of contact for greater reliability of the structure. For fixing this “slingshot” will install the lock bolt, in order not to cut a suitable thread into a hole should the hole just weld a suitable nut, which already and will install our bolt
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиGo to manufacture “mechanism” through which will be lifting and lowering the sling to the desired height. The mechanism itself, we will be the most simple, namely the screw. We again want the tube, but this time it is necessary to cut off approximately 15-20 centimeters.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиNext, you need to choose a powerful stud and a couple nuts. Nuts should be tightly sits inside our pipes. The length of the stud selected at random, its length will depend on the maximum height. Insert the nut into the pipe and securely weld them in.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиGo to the Assembly the tripod on which our props and will be installed. For this tripod you need to take the square metal profile and to cut away the three identical segments. Then you need to cut the ends of each blank under the angle under which we of the weld (see photo).
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиPrepare their feet naturally should be welded to the pipe nuts are made a bit earlier. Weld the legs are at the same distance from each other. And in the end we should get receivina design, here most importantly, our tripods, standing on the surface, did not crash any parties.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиSpin the pin in the stand and at the end of the stud must be screwed a couple of nuts. The nuts should be screwed with a small gap between each other, namely with a gap equal to the diameter of the bolt attaching the slingshot. Set the slingshot on the pin and check the correct position of the nut are with us, that is, when tightening the bolt on the catapult, it should not be removed, and Unscrew the nut when the latter is removed. Making sure that everything is in order weld nuts to the stud so that they have not changed their location in the future.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиThen for easy height adjustment support, to be welded to the hairpin arm. The handle itself is cut from sheet metal, the handle should be of a trapezoidal shape. Weld the arm to the bottom of the studs (see photo).
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиOur next handmade you need to put on the wheels. You can use the furniture wheel or wheels of the suitcase. To be able to secure the wheels on the legs to be welded to the legs of flat metal squares that need to be done through the mounting hole for your chosen wheels.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиYou’re done! It remains only to paint the scratch to protect it from the harmful effects of corrosion and you can start to operate.
Простой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиПростой винтовой подпор «рогатка», для удобной работы с длинномерамиHere is a video of the author of the homemade:
Well, thank you all for your attention and good luck in future projects the homebrew!

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button

Please disable your ad blocker

We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.