DIY

Grinder of the grinder with your hands

  • Instructions for making grinder from grinders with their hands
  • Grinder is a grinding machine used for final machining. Represents a wide sanding belt, rotating on the shafts by an electric motor. The most widely used grinder in knife making, tool sharpening. Grinder allows most exactly and at the correct angle sharpening of the cutting edge, and also prevents overheating of the material and loss of metal properties.

    Today we will show you how to make this machine, again, which is done manually it is not only saving your money, and in order to make it build for your needs and the specifics of production.

    Materials needed:

    1. Shaped tube 20×20 mm;
    2. Pieces of the steel band 40 mm, 50 mm;
    3. Angle steel 30 mm;
    4. Sleeve cable aluminum and the bearings for its size;
    5. Steel spring required of elasticity;
    6. The necessary hardware, screws, bolts, nuts.

    Tools needed:

    1. LBM;
    2. Elbow building;
    3. Vernier caliper and ruler;
    4. A simple pencil;
    5. Drill press or drill stand;
    6. Screwdriver with drill, an attachment for counter boring and bats;
    7. File flat;
    8. Welding machine and electrodes;
    9. A set of taps and dies for threading;
    10. Protective gloves and robe;
    11. Hammer;
    12. Clamp;
    13. Sander;
    14. Wrench set;

    Instructions for making grinder from grinders with their hands

    So, start with the fact that mark material for cutting grinder parts frame our grinder and other details. Then from the old angle cut using the grinder detail that will serve as the sole part which will abut the rear portion of the sanding belt when pressing on it.

    Гриндер из болгарки своими руками

    After working with svarochnik get a kind of frame.

    Гриндер из болгарки своими руками

    In the ever-spot weld the nut and steel strip, do the moving element of our stanochek.

    Гриндер из болгарки своими руками

    Then sawn off at an angle to the steel belt, screwed in the nut, on the edge of the frame. From the sawed off piece of steel make a rectangle that will serve as the focus of our steel strip.

    Гриндер из болгарки своими руками

    Using a screwdriver, grinders and taps make the hinge part.

    Гриндер из болгарки своими руками

    Hang the spring on our moving steel strip.

    Гриндер из болгарки своими руками

    From steel strips cut two rectangular plates and drill them in the 2 holes at the edges, it could be the brackets of the machine.

    Гриндер из болгарки своими руками

    Next, fasten big bolts and sole in the prepared in advance, they serve as axes of rotation of the shafts of the machine. Cut an aluminium sleeve according to the size and inserted into selected segments of the sleeve bearings, then placed on the bolts.

    Гриндер из болгарки своими руками

    Pay attention to the fact that the hinge element is needed for angle adjustment of the rotating sanding belt. Adjust the tilt using the screwing or unscrewing of the thrust bolt. It is registered so:

    Гриндер из болгарки своими руками

    Further, from the steel strips make a kind of bracket under GRINDERS

    Гриндер из болгарки своими руками

    and the bracket on which it will move along with angle GRINDERS.

    Гриндер из болгарки своими руками

    On the main frame weld two bolts after fitting, it will slide to the above design.

    Гриндер из болгарки своими руками

    They screw the nuts contribui and install the washers.

    Гриндер из болгарки своими руками

    Next, attach the bracket angle GRINDERS are the long-bodied nuts.

    Гриндер из болгарки своими руками

    Secure our LBM on the bracket and screw on its axis prepared from the aluminum liner of the shaft.

    Гриндер из болгарки своими руками

    Finally, put the sanding belt. Check the course. Run and adjust the incline.

    Гриндер из болгарки своими руками

    But that’s not all! Make of steel strip is a box, which will serve as a bracket for the fence.

    Гриндер из болгарки своими руками

    Fasten it to the bracket on the underside of the machine.

    Гриндер из болгарки своими руками

    Further produce thrust bar and fasten to the bracket.

    Гриндер из болгарки своими руками

    And finally, our GRINDER is ready!

    Гриндер из болгарки своими руками

    Grind small parts, sharpen knives and home-made instruments, but do not forget to secure the grinder on the work surface! Wish you success in all your endeavors!

    Manufacturer of grinder from the grinder with your hands look at the video:


    Source:

    rukikryki.ru

    Show More

    Related Articles

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    Back to top button

    Please disable your ad blocker

    We know you are here for the stories. Not the ads. But we need the ads to keep the lights on. So please whitelist Buzzon.live.