DIY

How to make a pusher for a circular saw

Hello dear readers and homemade products!
How to make a pusher for a circular saw When working with a circular saw and other machines, it is necessary strictly observe safety precautions. For this reason, a wide variety of devices are used to move and control the workpiece at a hand-safe distance.
One of the common devices are pushers. As you know, they quickly wear out the “tooth” with which the workpiece clings.
In this article, the author of the YouTube channel “Ohyo56” will tell you how you can make a push-type pusher with a removable and adjustable tooth.
This project is very simple for repetition in a carpentry workshop, and it only needs plywood trimmings.
Materials needed for DIY.
– Film faced plywood, thin board
– Silicone sheet
– Self-tapping screw with a press washer, wood glue, sandpaper.
Tools used by the author.
– Miter saw + circular
– Saw blades for wood
– Screwdriver
– Steel F-shaped clamps
– Screwdriver with a set of bits
– Tape measure, square, marker, file, knife.
Manufacturing process.
So, the main material for the body will be thick single-sided film-faced plywood. Two workpieces with a length of 200 mm are cut from the trim. This will be the length of the hull.
How to make a pusher for a circular saw  How to make a pusher for a circular saw By moving the parallel stop to the disc at a distance of 60 mm, the workpieces are cut in width (this is already the height of the future body).
 How to make a pusher for a circular saw How to make a pusher for a circular saw Both parts folded together, and a wooden plank with a thickness of about 15-20 mm is tried on to them. Its width should be slightly less than the body's width.
 How to make a pusher for a circular saw How to make a pusher for a circular saw A tooth about 10 cm long is cut from this strip.
How to make a pusher for a circular saw How to make a pusher for a circular saw Now the overhang of the saw blade is set to half the bar width. , opposite to lamination), grooves with a width equal to the thickness of the strip are formed in several passes.
How to make a pusher for a circular saw  How to make a pusher for a circular saw How to make a pusher for a circular saw The halves of the body and the tooth are being assembled for trial.
How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw Both halves of the case are glued together and tightened with clamps. In this case, you need to check that the edges of the grooves coincide with each other.
How to make a pusher for a circular saw  How to make a pusher for a circular saw How to make a pusher for a circular saw After the glue hardens, a thin through hole is drilled in the back of the case to the groove. The screw that fixes the tooth will be screwed into it.
How to make a pusher for a circular saw Now clamps you can remove and clean off the excess glue with a knife or chisel.
How to make a pusher for a circular saw How to make a pusher for a circular saw  How to make a pusher for a circular saw The edges of the body are aligned on the miter saw. It also cuts off the upper front angle at 45 degrees.
How to make a pusher for a circular saw How to make a pusher for a circular saw Returning to circular saw, the master aligns the sole and the upper surface of the body.
How to make a pusher for a circular saw Behind the scenes, the author made just such a wooden handle, which is glued to the upper part of the case, and temporarily pressed with clamps.
 How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw The handle is like this the form fits comfortably in the hand, and has a forward tilt, which allows you to simultaneously push and press the part against the sawing table.
 How to make a pusher for a circular saw How to make a pusher for a circular saw Almost everything is ready, it remains to sand the non-laminated surfaces and saturate them with linseed oil.
This is how the replacement tooth is inserted into the housing. The distance at which it protrudes from the bottom of the hull is easily adjustable.
How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw To fix the position of the plate, a self-tapping screw with a press washer is suitable. Before screwing into place, the edge of the self-tapping screw must be ground off with a file.
How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw In the front part of the sole, the author glued a piece of silicone sheet .
< a href = "https://usamodelkina.ru/uploads/posts/2021-04/1619388638_ps-128.jpg" rel = "prettyPhoto">How to make a pusher for a circular saw How to make a pusher for a circular saw How to make a pusher for a circular saw As you can see , with the help of such a pusher the workpiece is reliably controlled in two planes.
How to make a pusher for a circular saw How to make a pusher for a circular saw  How to make a pusher for a circular saw How to make a pusher for a circular saw Also this device can be used as a side stop, which is convenient when cutting small parts.
How to make a pusher for a circular saw How to make a pusher for a circular saw  How to make a pusher for a circular saw Thank the author for a simple but useful adaptation for the carpentry workshop!
Good mood, good health, and interesting ideas to everyone!
Subscribe to the telegram channel site so as not to miss new articles.
Author's video can be viewed here.

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button