DIY

How to make a sandpaper cutter

Hello dear readers and homemade products!
How to make a sandpaper cutter One of the consumables in any workshop is sandpaper, which constantly has to be cut to size for fixing in various holders. Cutting sandpaper with a knife or scissors is far from the best solution, the blades become dull very quickly, and every time you have to mark the sheets.
John, the author of the YouTube channel “John Heisz – I Build It”, has a large carpentry workshop, in which sandpaper is constantly consumed. In this article, he will tell you how you can make a device for quickly cutting sandpaper to the desired size.
Such a device is quite simple to make, for which trims of planks and plywood are suitable.
Materials necessary for homemade products.
– Sheet plywood
– Oversized washer, wood screws
– Circular knife
– Joiner's glue, sandpaper.
Tools used by the author.
– Screwdriver
– Electric Neyler
– Circular or hand-held circular saw
– Spring clamps, F- clamps
– Screwdriver with a set of magnetic attachments
– Tape measure, square, pencil, grinding block.
Manufacturing process.
John first cut out a rectangular base from 6mm plywood, along with two strips for the restraints, the same length as the base. Everyone can choose the optimal size of the device for himself (for the size of a sheet or strip of paper).
How to make a sandpaper cutter Then both strips are glued along the edges of the upper part of the base.
How to make an abrasive paper cutter How to make a sandpaper cutter To prevent the workpieces from moving, the master shoots them with carnations using a nailer . < br> How to make a sandpaper cutter In this case, the distance between the guides is chosen so that a whole sheet of paper fits between them , or strip.
How to make an abrasive paper cutter For a while gluing, guides are additionally fixed with spring clips .
How to make an abrasive paper cutter Next, a T-shaped guide is cut out of the board (or timber) for the entire width of the base with supports. Also, two L-shaped parts for the carriage are procured, the “step” on which should be slightly larger than the thickness of the edge of the guide.
 How to make a sandpaper cutter Joiner's glue is applied to the edges of two blocks of the carriage, and a rectangular plate is glued to them.
 How to make an abrasive paper cutter How to make an abrasive paper cutter How to make a sandpaper cutter After fitting, the guide is removed and the carriage parts are connected with studs.
How to make a sandpaper cutter How to make a sandpaper cutter A small handle is attached to the carriage cover.
How to make an abrasive paper cutter The author uses an enlarged washer sharpened around the perimeter as a knife. You can also use factory blades for circular cutter .
How to make an abrasive paper cutter To To make the circular blade work well even with a blunt cutting edge, the master offers an interesting solution.
In the middle part of the front side of the base, across it, a shallow cut is made using a circular saw. The width of the slot should be small (preferably using a thin saw blade) so that the washer or blade disk fits as tightly as possible in it.
The slot is formed with a slight approach to the side support strips.
How to make a sandpaper cutter  How to make a sandpaper cutter How to make a sandpaper cutter A pilot hole is drilled in the side of the carriage. A self-tapping screw is screwed into it, fixing the disc blade.
Here you should take into account the depth of the slot created in the base, and the distance from the carriage to the surface. The edge of the disc should only slightly not reach the bottom of the slot.
How to make an abrasive paper cutter How to make an abrasive paper cutter the disc is put on the guide, and the disc is inserted into the slot. The edge of the guide is marked on one of the side supports.
 How to make a sandpaper cutter How to make an abrasive paper cutter For the second support, the label is moved at the same distance from the edge.
How to make an abrasive paper cutter It remains to apply glue, align the guide along the marks, and fix it with nails to the base. After the glue has hardened, the surfaces and edges of the device must be sanded, as well as saturated with linseed oil. Such a simple impregnation protects the product well from moisture.
How to make a sandpaper cutter How to make an abrasive paper cutter  How to make a sandpaper cutter As you can see, the slots in the side strips are needed so that the disc can be moved beyond the edge of the working field. This will allow you to freely load a sheet of sandpaper into the fixture.
How to make a sandpaper cutter How to make an abrasive paper cutter  How to make a sandpaper cutter How to make an abrasive paper cutter To cut the sheet, just move the carriage.
 How to make a sandpaper cutter How to make an abrasive paper cutter For the convenience of cutting, the contours of the sandpaper holder sole are transferred to the base surface.
How to make a sandpaper cutter How to make a sandpaper cutter How to make an abrasive paper cutter How to make a sandpaper cutter How to make an abrasive paper cutter How to make a sandpaper cutter  How to make a sandpaper cutter Thanks to John for the design, and advice on making a simple cutter for sandpaper.
Good mood, good health, and interesting ideas to everyone!
Subscribe to the telegram channel site so as not to miss new articles.
Author's video can be viewed here.

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button