DIY

A tool that can be used to mark the cut-off contour of any pipe

A tool that can be used to mark the cut-off contour of any pipe Good day, dear homemade friends! In this article, we will take a closer look at making homemade products useful for any builder. Often when building something, you have to cut pipes. It would seem that a fairly simple task, and no problem can arise here, mark and saw off. But just at the “mark” stage, these same problems may arise, since it is not easy to mark the place of the saw cut on a round pipe, and often some kind of curve emerges, along which it is then not clear where the required length is. Yes, there are of course different tricks for this, but when you need to make a couple of dozen or even hundreds of cuts, tinkering with tape or scotch tape is not easy and it takes a lot of time. So this homemade product will just help you leave marks in the exact place and do it quickly and easily. Well, well, I think you shouldn't delay with a long preface, let's go.
To assemble this homemade product, we need the following, namely:
– Thick metal sheet (metal plate)
– Several bearings
– Nuts
– Screws
– Bolts
– Metal washers
– Metal corners
– Self-tapping screws
From the tools we also need the following:
– Ruler or tape measure
– Marker
– Drilling machine or ordinary drill
– A set of drills of the required diameter and a conical lead for countersinks
– What kind of lubricating oil – – Chisel
– Hammer
– Vise
– Some kind of paint to protect homemade products from corrosion – – Welding machine – All necessary accessories for working with a welding machine – Bulgarian
– Cutting and grinding discs for a Bulgarian
Manufacturing universal pipe marker:
As befits when building any homemade product, the assembly must begin with a part that will serve as the basis and on it, in turn, the entire structure will be built. With us, this part is just the base, which will be attached to the table or floor, the rest of the structure will be installed on it. We will use a sheet of thick metal as such a base. Or you can use any metal strip that is made of thick metal.
A tool that can be used to mark the cut-off contour of any pipe Having decided on the choice of the base. From the workpiece you have chosen, you need to saw off two absolutely identical rectangles. Two, because the instrument itself will be in two parts. On which the pipe will rest, this is necessary to ensure the versatility of the structure itself, since you can arrange these parts at any distance from each other, then you can work with pipes of any length, which you will agree is quite convenient.
 Tool that you can mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe Next, in our newly cut metal rectangles, you need to drill several through holes. Namely, one through hole on both sides, right at the very edges. These holes will serve as fastening holes for us, thanks to which the ready-made tool will be attached to any surface already in operation. This surface can be a table, bench, board, floor, etc. Since the material selected is quite thick, and to make it easier for you to drill such thick metal, use some lubricating oil that will reduce friction and the drill will run like clockwork. Thus, you minimize the risks of overheating an expensive drill.
A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe After drilled in each of the metal rectangles, two through holes. They need to be widened otherwise “siphoned” for this you need a specially created cone drill for metal. Of course, this is not necessary at all, but flush-mounted screws look much more aesthetically pleasing than protruding ones. If you do not care about the aesthetic part of the homemade product, but only need the practical part of it, then you can actually skip this step.
A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe Let's go further. Now we need to make “V” -shaped parts on which the pipe will be laid. You can make these very parts from metal strips by welding them at an angle, or simply bending these same metal strips at the desired angle. For this, the author decided to use corner pieces, which in the cut have a shape suitable for us. The pipes available for processing directly depend on the corner you choose. The larger the corner, the larger in diameter the pipe can lie on it. But if the corner is too large, then the narrower pipes will fail, and you will not be able to work with them. Therefore, decide the size of these “V” shaped parts for yourself, based on your needs.
A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe As it was not difficult to guess, after sawing off two small pieces of the corner, they must be welded into our previously prepared blanks. They must be welded with an angle exactly in the middle of the rectangle, that is, in the same way as shown in the photo below. There is an important point here that is worth mentioning. It is very important that these two parts are exactly the same, otherwise the pipe that you will put on them will simply not stand and will actually fall. Therefore, we add these two parts as the author did and clamp them in a vice.
 A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe Having thoroughly welded all joints of the blanks. We grind the welded seams using a grinder or a drill with special grinding discs. This is the same as the countersink only affects the visual component of the homemade product.
A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe Moving on to the bearing mountings. The bearings will be mounted and rotated by screws, which in turn will be attached to the ends of the “V” shaped pieces. We now need to weld these same nuts, but this must be done so that they are installed exactly relative to each other. It is important that the pipe rests on all eight bearings at the same time and that none is idle. Just to set all the nuts to the level, you need to screw these nuts onto the long bolts. The hooks should be at the right distance from each other (such that they are located along the edges of these same corners). And now, in this position, it is necessary to weld the nuts to the “V” shaped elements.
A tool that can be used to mark the cut-off contour of any pipe A tool with which you can mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe We apply the bolts with the hooks screwed on them to the “V” -shaped elements and press these bolts to the workpieces using a clamp or clamping them in an ordinary vice. First, we grab all the nuts, once again make sure that all the nuts are on the same plane relative to each other, and having already made sure of this, we weld the connections well. After welding, as always, we grind all welded seams.
A tool that can be used to mark the cut-off contour of any pipe A tool with which you can mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe Then we take eight screws suitable for the thread to our nuts and, accordingly, eight matching the bearing diameter. Taking the screw, we put a bearing on it, if necessary, a metal washer can be put on the screw so that the bearing does not fly off, and we screw the screw and nut into the welded nut, from the outside of the structure. We repeat the same steps with all the remaining screws and bearings.
 A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe And you're done! It remains, if desired, to paint the homemade product to protect it from corrosion. And you can already use it. You can see how to use it below.
A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool with which you can mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe A tool that can be used to mark the cut-off contour of any pipe Here is a video of the author of the homemade product:

Well, thank you all for your attention and good luck in future projects myself Buyers!

Source:

usamodelkina.ru

Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button