I decided to make a key holder in the corridor. I was told, “the distance is 6cm.” After reading the message, I immediately set about making a key holder on a motorcycle theme.
I decided to squeeze a small present into this size.
I type in the search engine “ jigsaw wooden motorcycle “. A lot of different things fall out.
From the large version of the pictures I chose which is simpler, there is only 6 cm. I will have to make a narrow bar.
I bring the picture to the monitor, that's bad luck, a bit big and not quite correct. The rear wheel of a sports bike is much larger and thicker. Okay, I can draw myself. Quickly sketching a drawing with a pencil on the first piece of paper I can find a motorcycle.
I correct the drawing a little with a ruler and compasses. Then I rub on the back with a charcoal pencil. Everything is ready to be translated into plywood.
I take the side wall from the desk drawer. She's a little with a secret, I'll show you later. I cut the right size with my wonderful homemade fine-toothed saw.
Then I translate the drawing with a pen.
While cutting with a jigsaw, I found an annoying error. Wheels are the same size. I start cutting out the picture and immediately slightly correct the dimensions of the wheels, the front is slightly smaller, the rear is larger.
I cut out the key holder itself from the same blank from the desk drawer. … There is a nice drawing of a tree underneath. A little work with sandpaper and all the beauty at a glance.
Trying on a motorcycle on a die, it looks okay.
they will go with bamboo skewers for kebabs. I cut off the desired size with a jigsaw.
I clamp the sticks in a screwdriver and use sandpaper to round the ends.
I am selecting a drill of the required diameter from a recently made cluster. I wrote an article on how to make it on our website.
I didn't like the mess with drills in the model. I quickly assembled such a piece of plastic panels. Glued with cyacrine.
First, I drill a control hole and try how the skewer enters.
Then, at an angle, I drill into the key holder's plate itself.
Everything entered very clearly and with interference. Corrected with a hammer.
Then he covered all the pieces of wood with “electric” varnish. I don’t know how he fits on the electrics, he walks just fine on wood. Dries up right before our eyes, though the infection stinks. I had to open the window.
I stick a pin into the motorcycle and paint cheerfully with varnish. Reveals wood texture very well, by the way!
Then I wash the brush with acetone and wipe it.
Just in case, I spill the sticks from the back with cyacrine. I drill a hole for a screw in a sweep. After screwing it into the wall, I'll glue the motorcycle on top.
Everything is ready for a gift.
In the course of a telephone conversation about six centimeters, clarification follows.
In the wall of the corridor, two homeless nails “THE DISTANCE BETWEEN THEM ARE SIX CENTIMETERS” were found !!! I translate the image of the motorcycle. Now it turned out to be just the right size.
Slightly correct the drawing with a ruler and a compass, draw a larger rear wheel.
I rub on the back with a black pencil and use a pen to transfer the image onto thick plywood.
I cut along the contour with a small special jigsaw and file number three.
Then you need to cut out the inner rims of the wheels. I drill holes in the sharpest places with a 2mm drill. When I cut it, it will be better to unfold the file almost in the opposite direction. It seems that everything went well, slightly straightened the motorcycle with sandpaper.
two tiers. I mark and cut out the first 4mm plywood overlay.
I mark the second overlay from a beautiful piece with a pattern. Not economically true, but beautiful.
I mark and cut out the suspension elements, on those same two nails and six centimeters between them.
Then I cut the key suspension sticks again and a bamboo skewer and round off the ends with sandpaper using a screwdriver.
I drill three holes at an angle. I hammer pistils into them.
I'm assembling the whole structure on cyacrine.
nails, if there really are six centimeters between them!
And again I cover it with smelly electric varnish in two layers, right away my brush in acetone.
The second gift option is ready. You can visit.
Well, if there is not six centimeters between the nails …. I don't know what will happen !!!
Take some candy!